La Grange, TX

When I arrived I found that the indoor air circulation system was faulted. I spoke with the client about his options repair vs replacement. I went over the options for repair and he wanted me to give him some options for replacement also. The client will let us know what he wants to do after he speaks with his wife.

Upon my arrival I completed the warranty repair on the blower housing for system number 1. After completing the repair I tested the system and verified it was operating to manufacture specifications. I then pulled the return air grill from the kitchen area and chemically washed the grease off outside. Reinstalled the return air grill and secured duct back to it.

Upon my arrival, I spoke with customer about their concerns with the system, not cooling well. Performing my diagnostics. I found that the voltage enhancement system had failed, causing the outdoor compressor to not come on for normal operation. I spoke with the customer about my concerns and went over repair options. they approved to have the system repaired today. I performed the approved repairs then wash the condenser coil due to it being dirty so I can get an accurate read on pressure. Found the system is operating properly at this time. It will take a while for the temperature to come down in the home given it was 94° in the home. Customers are going to let the warranty run out on the home and then consider joining the maintenance program.

Arrived to site and replaced improperly installed water removal system. Put vent after the P trap. Added a union for easy clean out in the future. Glued all connections and insulated whole line with armaflex and tape. Tested water safety switches and chemically treated new water removal system line with pan treatment spray. Washed down condenser with water. Was very dirty on the back side with yard clipping. Tested system in cooling, system operating and draining to manufactures specifications at this time.

Customer was concerned about RTU #3 not coming on and cooling. Got on roof and began to diagnose the system. Refrigerant circulating pump would come on, but not the air movement system. Voltage distribution system for air movement system not receiving 24 volts to pull in and distribute voltage. Traced issue back to the air movement system relay. Relay was faulted. Replaced relay and air movement system came on with the refrigerant circulating pump. Checked pressures in cool and found that the refrigerant pressure control system was not operating as it should giving us faulty pressures. System is cooling, but not to manufactures specifications. Informed customer of our findings, and will be getting with supply house on Monday to check availability and price of a new refrigerant pressure control system. Heat transfer media coil needs to be chemically cleaned as well as the drain pan underneath. Will update customer next week on a repair time. System cooling to the best of its ability at

Arrived on location to swap out faulty blower motor shaft and pulley for RTU #2. After pulling blower motor assembly we were unable to get the Allen key shaft locking screws off. Broke 5 different Allen key the process of trying to get it loose. Could not use heat due to the rubber bearing outside shaft. Will return with hardened steel bits that will not break. Replaced remote sensor for unit number 8.

Upon my arrival I spoke with the customer about their concerns with the system not cooling. Performing my diagnostics I found that the voltage enhancement system has failed causing the outdoor unit to not operate. I spoke with the customer about their different options for repair and they chose to go with HN14E. I performed the approved repair installing a new voltage enhancement system, new voltage distribution system, added performance enhancement system, added DTK power protection, redid wire terminals, cleared leaves from inside the condenser, chemically washed the condenser coil then ran a performance and safety testing. System is operating within manufacture specifications at this time. Customer joined the maintenance program as well.

Upon my arrival in La Grange I did AC Maintenance. the air movement system was cycling on and off. When I checked the voltage coming from the relay control it was opening and closing causing the issue. This is going to be the main cause of the system freezing over. With the customers approval I replaced the relay control and redid the wire terminals on it. I then tested the system and found that everything is operating properly at this time.

Arrived in La Grange for AC Repair, Upon my arrival I evaluated two mini split systems and one furnace straight, cool split system. I verified system safety and performance is to manufacture specifications. Flushed and treated the water removal system. Cleaned the electrical cabinet and washed unit using water. Found that the furnace split straight cool system was low on refrigerant. I performed a leak check with my electronic leak detector and found multiple signs of refrigerant leaks at the indoor unit. My recommendation was for scheduling an appointment with the comfort advisor regarding potential repairs.

Arrived in La Grange for AC Maintenance, Upon my arrival I performed a diagnostics on RTU#7 finding that the low voltage wire on one of the relays was loose causing low voltage to not reach the indoor air movement system. I pulled the spade connector off and crimped it to allow for a tight connection on the relay. Testing the system I found that everything else is operating properly at this time.

Arrived in La Grange for AC Maintenance, Upon our arrival we spoke with the customer about their concerns with the system shutting down. Performing our diagnostics we found that the system is a negative pressure system and was not equipped with a vent after the ptrap as well as the water removal system was backed up. We spoke with the customer about our concerns, went over repair options and maintenance program. Customer approved HF3A and the maintenance today. We cleared the water removal system, installed a vent pipe and checked the system performance. Found everything operating properly at this time.

Upon arrival in La Grange, Mini split outdoor unit non-operational. Found bad inverter board due to voltage surge. Replaced board and tested compressor start-up sequence. System now cooling effectively across all zones.

Upon arrival in La Grange, Swapped aging unit with high-efficiency model. Installed new thermostat, sealed duct transitions, and tested airflow. Verified TXV function and checked for proper defrost operation. System now meets ENERGY STAR standards.

Upon arrival in La Grange, System not cooling due to low refrigerant. Found leaking Schrader valve. Replaced valve core, pressure-tested, vacuumed, and recharged to spec. Verified cooling operation and recorded a 21°F temperature differential.

Upon arrival in La Grange, Seasonal cooling maintenance included pressure readings, capacitor testing, and evaporator coil inspection. No major issues found. Static pressure slightly high—recommended ductwork inspection to reduce strain on blower motor.

Upon arrival in La Grange, Serviced three indoor heads. Cleaned washable filters, cleared drain tubes, inspected refrigerant line insulation. Verified compressor operation and inverter modulation. System passed all function tests without faults.

Arrived in La Grange for Conducted comprehensive tune-up. Measured voltage and amperage, cleaned drain line, and lubricated fan motor. Tested temperature drop across coil and ensured proper compressor cycling. System is performing at optimal capacity.

Arrived in La Grange for AC Maintenance, Investigated indoor head not responding. Found faulty thermistor sensor not signaling temp to control board. Replaced sensor and verified accurate feedback on display. Unit is cooling efficiently again with correct temperature modulation.

Arrived in La Grange for AC Maintenance, Diagnosed intermittent cooling. Found worn contactor causing voltage drop under load. Replaced with OEM part, tightened all high-voltage connections, and verified stable amp draw. Customer educated on electrical inspection intervals.

Arrived in La Grange for AC Tune-up. Replaced R-22 unit with a new R-410A 15 SEER system. Replaced line set due to incompatible oil. Installed matching coil, set system on leveled pad, and calibrated airflow at 400 CFM/ton. System now operates at 100% efficiency.

Arrived in La Grange for AC Maintenance, Routine cooling check. Inspected blower wheel, measured temperature split (19°F), and checked airflow with anemometer. Found minor duct leakage in return plenum. Recommended sealing to improve system performance and reduce humidity.

Arrived in La Grange for AC Maintenance, Upon my arrival I spoke with the customer about their concerns with the HVAC system not cooling. Performing my diagnostics I found that the voltage enhancement system is faulted. I checked the plug on the refrigerant circulation pumping system and found that the wires had burned and the system went to ground. I spoke with the customer about the age of the system and gave recommendations on having a comfort specialist come out. Their consult is set up for 5/13/25 in the afternoon. Customer would also like options emailed one for repairs to compare.

Upon my arrival in La Grange, for an AC service, I installed the comfort control system. The system had to perform an update while I was on site. After the system updated I tested the equipment and found everything operating properly at this time. I was unable to get the app to work through the customer’s phone. I informed him he would have to contact the Support line to see if they can help get it hooked back up if they can’t Daryl says he will come out tomorrow.

Today I arrived in La Grange, for an AC service, with concern the outside heat pump does not turn on when the thermostat is in heating mode. Customers had previously found thermostat blank one morning. The indoor unit breaker was tripped, they turned breaker on and system was operational approximately 3 weeks at that time the thermostat was blank again so they installed a different thermostat. Since then the cooling works but in heat it doesn’t. I found thermostat was proper for the type of system they own. The thermostat model they had only allows operation for heat and cool, no auxiliary heating. I spoke with customer about heat pump systems and we also spoke about our maintenance plans.

Heat Pump Repair in La Grange, TX today for a great client. Specialized heat pump repair addressing intermittent system failure. Conducted comprehensive diagnostic assessment using advanced electrical diagnostic tools, identified and replaced faulty integrated control board, recalibrated system parameters, and verified full operational integrity through complete system performance test.